How To Repair Or Replace A Locking Mechanism On A Patio Door

The door lock cylinders on the doors of your machine are not just there to protect y'all and your family while you lot're in the vehicle. They likewise protect the vehicle itself from theft.

Whenever you turn the fundamental in the driver or passenger side door, the door'southward latch mechanism should either lock or unlock the door. However, a worn-out cylinder can make it difficult to lock or unlock. In extreme cases, the cylinder will either non release the key or cause the primal to break off in the door.

• Annotation: Keep in mind that when you change the door lock cylinder, you need to go a new one from the manufacturer that has the same key cutting as your old ane. If you are unable to obtain a lock cylinder with the same vin as your vehicle, you would then demand to also replace the ignition tumbler and the lock cylinder in the trunk, if your vehicle is equipped with a trunk.

Function 1 of 5: Verifying the condition of the door lock cylinder

Materials needed

• Ratchet with metric and standard sockets
• Cantankerous tip, or Phillips caput, screwdriver
• Door panel remover
• Flat head screwdriver
• Needle olfactory organ pliers
• New door lock cylinder specific to your vehicle
• Torques flake set
• Bicycle chocks

Step 1: Locate the door with the faulty door lock cylinder. Visually inspect the damaged, stuck, or broken door lock cylinder for any exterior damage.

Lift up on the door handle to run into if in that location is any bounden of the mechanism within the door. This confirms that the lock cylinder has failed and not the linkages within the door.

Step 2: Unlock and open up the affected door. Get into the vehicle from some other door if the door you are working on will not open up. Unlock and open the door with the broken, stuck, or damaged door lock cylinder from the inside of the vehicle.

Step 3: Manually lock the affected door and test it. Lock information technology by pushing on the latch on the side of the door. Endeavor operating the damaged lock cylinder by putting the key into the lock and turning it to unlock the door.

Part two of five: Preparing the vehicle

Step 1: Park your vehicle on a apartment, difficult surface. In order to safely work on your motorcar, information technology cannot be on an incline. Find a apartment, hard surface on which to work.

Step two: Place wheel chocks around the tires. Engage the parking brake and put cycle chocks in place to the go on the tires from moving.

Stride 3: Install a nine-volt battery saver. If your vehicle has electronic door locks, you volition demand to disconnect the car battery. Before doing and then, plug a nine-volt battery saver into your cigarette lighter.

This will keep your estimator live and keep your settings current in the vehicle. If you do non have a nine-volt battery saver, though, that's okay.

Step 4: Disconnect the battery. Open up your vehicle's hood in order to take the ground cable off of the bombardment's negative post; this will disable the ability to the air-to-fuel ratio sensor.

• Tip: If you have a hybrid vehicle, refer to the owner'due south transmission for instructions on disconnecting the small bombardment simply.

Once yous're done disconnecting the bombardment, close the hood.

Part 3 of v: Removing the old door lock cylinder

Step i: Unlock the affected door. To begin, unlock the door where you will be replacing the door lock cylinder, either by using your primal or using the inside door lock.

Step 2: Remove the window creepo. After first making sure that the window is fully closed, remove the window creepo.

Pry up the plastic cover on the handle (the handle is a metal or plastic arm with a metal or plastic clip). Remove the cross tip, or phillips, caput screw belongings the handle to the shaft.

Then pull the handle off. A large plastic washer will come off with the handle. Have notes or a motion picture in order to remember which way this is supposed to sit down against the door.

Step three: Remove the door lock cluster panel. If your vehicle has electronic door locks, yous will need to remove the door lock cluster panel from the door panel as well.

When removing the cluster panel, yous need to remove the screws attaching information technology to the door panel. If the cluster is unable to exist detached, y'all may exist able to disconnect the harness connectors under the door panel equally you pull this off in a later step.

Stride 4: Remove any externally mounted speakers. Prior to removing the door panel, any speakers would need to be removed for those vehicles that have custom speakers externally mounted on the panel.

Stride v: Remove the panel on the within of the door. Gently pry the panel away from the door all the way effectually.

A flat screwdriver or a door panel remover (preferred) helps here, just be gentle so you don't damage the painted door effectually the console.

Once all the clips are loose, catch the console top and bottom and bend it slightly away from the door. Lift the whole panel straight up to elevator it clear of the catch behind the door handle.

• Notation: Equally yous do this a large gyre leap will fall out. This spring sits backside the window crank handle, and information technology will exist somewhat catchy to get dorsum into identify when you reinstall the panel.

Step 6: Remove part of the plastic sheeting. Pull the plastic sheeting away from the rear half of the door. If you practice this gently, you'll be able to reseal the plastic afterwards.

• Note: This plastic is essential in forming a water barrier inside the door panel, which is necessary because some h2o ever gets into the inside of the door during rainy days or automobile washes.

• Tip: While you are peeling back the plastic bulwark, you can too check that the 2 drain holes in the lesser of the door are clear and that there is no buildup of debris in the bottom of the door.

Step 7: Remove the door lock cylinder. Commencement slide your manus upwards to the back of the cylinder and use a pair of needle olfactory organ pliers to pull off the bracket clip property the door lock cylinder in identify. And so pull the cylinder out of the door from the outside (pushing from the inside if needed).

Step viii: Remove the piece that connects the cylinder to the lock indicator stalk. To do this, you volition demand to pull up the iii small tabs with needle nose pliers and detach to the remaining smaller subclass from the back of the cylinder.

Office 4 of 5: Installing the new door lock cylinder

Step i: Assemble the new door lock cylinder. Piece together the new door lock cylinder like the old one by putting the rubber gasket on the part of the cylinder that fit on the exterior of the car door.

Button the new small bracket onto the cylinder to concur the gasket in place.

Step two: Insert the new lock assembly. Put the complete lock associates into the hole in the door and marshal it with the cylinder slot.

Step 3: Connect the door lock cylinder. Replace the large bracket that holds the door lock cylinder tight to the inside of the door.

Pace four: Install the slice that connects the cylinder to the lock indicator stalk. Use needle olfactory organ pliers to push down the 3 small tabs and attach the remaining smaller bracket to the back of the cylinder.

Step 5: Replace the barrier. Place the plastic sheeting back confronting the rear half of the door and reseal it.

Footstep 6: Supersede the door panel. Reinstall the spring that sits backside the window creepo, then set the whole panel straight onto the door and slide information technology over the locking knob. Be sure not to move the spring.

Identify all of the console clips into the holes in the door and with a firm tap, snap all of the clips dorsum in.

Footstep 7: Reinstall the door lock cluster panel if applicable. If your vehicle has electronic door locks, you volition need to reinstall the door lock cluster panel into the door.

Install the screws attaching the cluster to the panel, then brand sure the cluster is connected to the wiring harness. You may accept to attach the connectors under the door panel before you supplant the door panel onto the door.

Footstep 8: Supplant any externally mounted speakers if applicative. If the vehicle has custom speakers that are externally mounted on the door panel, these speakers will demand to be installed dorsum onto the door panel.

Step 9: Reinstall the window crank. Position the handle in identify with the large plastic washer and reinstall the plastic embrace.

Reinstall the screws that connect the handle to the shaft and secure them. Plow the window crank to ensure that the window can move upwardly and down. Install the plastic rim around the handle.

Step 10: Install the outer door handle. Pull the handle forward to release it and install it into the door. Install the two screws that will hold the door handle to the door beat.

Part 5 of 5: Reconnecting the bombardment and testing the cylinder

Step i: Reconnect the bombardment. Open the vehicle's hood and reconnect the footing cablevision dorsum onto the bombardment'due south negative post. Tighten the battery clench up tight to ensure that the connection is good.

Remove the nine-volt battery saver from the cigarette lighter.

Step 2: Test the new door lock cylinder. Test the new door lock cylinder past locking and unlocking the door with your key.

Lock and unlock it with the door open and with the door airtight. This ensures that the connection between the door lock cylinder and the door latch is working.

If you accept electronic door locks merely have a key lock cylinder, check to see if the outside handle locks by using a key in the door lock cylinder and by pushing down onto the inside lock push button. You can exercise this with the window downward and so you don't have to enter the vehicle.

If your door will not open even after replacing the door lock cylinder, and then in that location may be a deeper upshot with the door lock cylinder assembly or a possible electronic component failure in the case of vehicles with electronic door locks. If the problem persists, or if you're not comfy performing a repair like this yourself, you can always seek out help from a certified mechanic, such as one from YourMechanic, who can audit and address your door lock for y'all.

The statements expressed above are but for informational purposes and should be independently verified. Please see our terms of service for more details

Source: https://www.yourmechanic.com/article/how-to-replace-a-door-lock-cylinder-by-marvin-sunderland

Posted by: preblehimee1957.blogspot.com

Share this post