How To Repair A Chipped Ceramic Kitchen Sink

Download Commodity

Download Article

If yous've noticed a chip or crevice in your ceramic sink, don't worry! Y'all can apply epoxy for a quick and like shooting fish in a barrel way to repair the surface. In this article, nosotros'll walk you through the entire procedure, starting with how to clean and prep the ceramic surface. Then, we'll explicate how to mix and apply epoxy to fill in any modest cracks and chips. If you're gear up to fully restore your ceramic sink and then information technology looks brand new over again, read on.

1. 1

   Sand the edges of the bit or cleft to smooth them out. Apply a very fine-grit sandpaper, such as 400-grit sandpaper. Lightly rub a piece of sandpaper dorsum and forth over the damaged area, feeling information technology with your fingertips as you become, until y'all don't feel whatsoever sharp edges.^[1]

   • Yous can skip this if the damage is very small-scale, such as a hairline crack that doesn't have abrupt edges.

2. 2

   Make clean the area to remove any loose droppings from the chip or scissure. Scrub the damaged surface area with an annoying cleaner like Ajax and a scrubbing pad or the scrubbing side of a sponge. Rinse the sink thoroughly with water from the tap.^[2]

   • This will ensure a clean surface for the scrap and crack filler to adhere to and course a strong bond.

   Tip: You can use the sharp tip of a pin or needle to scrape out hairline cracks or castor very small fries out with an old strong-bristled toothbrush to remove any pieces of ceramic or dirt that are stuck in them.

   Advertisement

3. 3

   Wipe the sink down with a towel and let it dry for at least one hour. Use a newspaper towel or a clean absorbent fabric to wipe abroad all the excess moisture in the sink after rinsing information technology. Leave the sink to air dry for at to the lowest degree 1 hour earlier y'all apply the repair epoxy.^[3]

   • Don't e'er apply chip repair epoxy to a wet surface or it will not cure correctly.

   Advertisement

1. 1

   Buy a porcelain and ceramic epoxy chip repair kit. Buy a generic white repair kit if your ceramic sink is a standard white colour. Become a kit that allows you to mix pigments to create custom colors if your sink is an off-white color.^[4]

   • Porcelain and ceramic flake repair kits come with two vials containing liquids that you lot mix together to create the epoxy filler, likewise as a brush you can utilize to mix and apply the production.
   • Y'all can buy these repair kits at a home comeback center, hardware store, or online.

2. 2

   Mix together the two parts of the epoxy chip repair kit. Open up the package and set the rigid plastic front piece on a flat piece of work surface to use as a mixing tray. Empty the contents of both vials into the tray, using the provided castor to scrape out any liquid that sticks in the vials. Use the brush to mix the liquids thoroughly in the tray for at least 1 minute.^[five]

   • Read the instructions on the packaging and defer to the manufacturer's instructions for any specific directions about how to mix the epoxy.

   Tip: If you purchased a kit that has pigments yous can use to alter the color of the epoxy, mix in the appropriate color of pigment 1 drop at a time until you get a match. For example, if your sink is light light-green, mix in a drop of dark-green pigment until the epoxy looks like the right color.

3. three

   Let the epoxy sit at room temperature for 30 minutes. Leave the tray with the mixed epoxy sitting on your piece of work surface for half an hr so the epoxy starts to cure. This volition make information technology thicker and easier to apply to fill in chips and cracks.^[6]

   • Again, defer to the manufacturer'due south instructions for the specific repair production you purchased for directions about exactly how long to wait earlier applying the epoxy.

   Advertising

1. ane

   Utilize the kit's brush to utilize a thin coat of epoxy to hairline cracks. Dip the tip of the brush into the tray to embrace information technology in epoxy. Carefully brush the epoxy into the cleft or flake, spreading it to the edges and being careful not to get information technology onto the surrounding surface of the sink.^[7]

   • If you lot apply too much epoxy and get it on the area around the crack, wipe away the excess with a moisture paper towel.

2. 2

   Push button epoxy into deeper gouges and chips. Use the tip of the repair kit's castor or a toothpick to scoop up a dab of epoxy. Push the epoxy into the flake with the castor or toothpick without overfilling it.^[eight]

   • Don't worry about making the chip level with the sink with the first layer of epoxy. You can keep applying layers until you get information technology simply right.

3. 3

   Await 45 minutes for the kickoff coat of epoxy to prepare. Leave the sink alone for 45 minutes one time you're happy with how the start glaze looks to let it cure. Brand sure nobody uses the sink if there is anyone else around.^[9]

   • You could write a alert sign and record information technology over the sink to ensure nobody uses it while the epoxy dries if this is a business concern.

4. 4

   Employ a second coat of epoxy using the kit's brush. Dip the tip of the brush back into the tray with the epoxy. Gently brush another layer of epoxy onto the repaired fissure or button it into the repaired fleck to finish filling in the damage.^[10]

   • Most minor cracks and chips only need two layers of epoxy to fill them in. However, if yous are repairing a deeper gouge, you can apply more than coats as necessary.

   Tip: You tin utilize the edge of an old credit card to smooth out the epoxy and cover the edges of the crack or bit to blend it in with the surrounding surface.

5. 5

   Allow the epoxy dry for 24 hours. Don't use the sink for a total 24 hours later on you lot apply the last glaze of epoxy. The epoxy needs fourth dimension to cure without getting wet in gild to bail permanently to the repaired area.^[eleven]

6. 6

   Sand the repaired expanse with fine-dust sandpaper. Use 400-grit or effectively sandpaper to smooth out the repaired surface area until it is blended in and even with the rest of the sink. Rub the sandpaper lightly back and forth over the chip or scissure and run your fingertips over it as y'all go until information technology feels completely polish.^[12]

   • Later you level out the repaired expanse, you lot tin can moisten your sandpaper or go the area wet and finish sanding information technology to shine it upward and assist blend it in with the residuum of the surface.

   Advertisement

Add together New Question

• Question

  What's the best manner to clean a ceramic sink?

  

  Melanie Garcia is the Co-Owner of Oranges & Lemons, a small, family unit cleaning business concern based in Downtown Los Angeles, California (DTLA) in operation for over 40 years. Oranges & Lemons operates while partnering with the National Domestic Workers Alliance and Hand in Hand: Domestic Employers Network.

  

  Professional Business firm Cleaner

  Skilful Answer

  

  Support wikiHow by unlocking this expert reply.

  Get a mild cleanser, similar Bar Keeper's Friend. Rub the cleanser over the ceramic and use a sponge to scrub whatever stains or dirt away. And so, just rinse the area off. You can repeat this procedure whatsoever number of times until y'all sink is blemish-free.

Inquire a Question

200 characters left

Include your electronic mail address to get a message when this question is answered.

Submit

Ad

Things You'll Demand

• 400-grit sandpaper
• Newspaper towels
• Scrubbing pad or sponge
• Abrasive cleaner
• Porcelain and ceramic epoxy repair kit
• Toothpick (optional)

Nigh This Commodity

Thank you to all authors for creating a page that has been read 17,359 times.

Did this commodity help yous?

Source: https://www.wikihow.com/Fix-a-Ceramic-Sink

Posted by: preblehimee1957.blogspot.com

Share this post